Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
The author is making a few great points about How to Install a Bathtub as a whole in the article down the page.
Setting up a tub isn't precisely brain surgery, yet it does need solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bath tub with a new one is likewise a moderately hard project. If the old bathtub is readily accessible, the task can relocate immediately; if you have to open a wall to remove the old bathtub as well as place the brand-new bathtub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will require an assistant to leave the old bathtub as well as set in the new one. See to it you have qualified yourself for the task as well as are comfortable attempting it. As opposed to employing a specialist to take over a halfway-completed project, it is far better to take into consideration using one prior to you start. Opportunities are you may require an expert plumber to make tube links.
This article will certainly assist you set up a new bath tub in your bathroom if you have actually currently gotten a new bathtub as well as don't require to change the arrangement of your previous water supply pipelines.
Your tools and also product checklist need to consist of the following:
Planning for the Setup
First of all, the supporting framework provided with the bathroom should be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to make certain that if the tap includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the versatile faucet ports to the bottom of both faucets using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is separate the water supply. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome because of the limited gain access to that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a towel ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to carrying on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for placement. The wood boards are valuable in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bathtub until the level reviews degree.
To set up taps, fit the bottom of the outermost adaptable faucet port to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water as well as inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub and additionally inspect the overflow outlet and also the regular outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub should wait till the tub has been made use of a minimum of once as this will certainly settle it right into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in area between the faucet and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The previous type needs to be attached to the tap ends first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture a rigid seal, triggering the water to pass through the wall between the bathroom as well as the tiling, bring about problems with moisture and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes and also cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to permit the motion experienced when the bathtub remains in usage. The sealer can split rather very early if you do not think about this activity before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily available on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading up on How to Install a Bathtub? Try leaving a remark down the page. We'd be interested to see your responses about this entry. Hoping that you come back again before long. If you appreciated our blog posting please remember to pass it around. Thanks a bunch for your time. Please check up our blog back soon.
Book Instantly Report this page